Courses

Test sequences creation and modification

 

TitleTest sequences creation and modification 
Attendees Operators of the quality assurance service, operators of the maintenance service 
ObjectivesProvide comprehensive information for a self-sufficient creation and modification of test sequences
RequirementsBasic informatics knwoledge, advanced knowledge of Microplan test rigs
Program

Operations with the test sequences:

  • Structure of the test sequences
  • Managing sequences with testSEQ

Editing test sequences:

  • Editing and settings
  • Editing a phase
  • Dependencies

Configuring and using basic tests (VI):

  • Parameters editing
  • VI features
  • Test failure
  • Using the simulator
User manualincluded
Duration24 hours
LocationMicroplan, Via Andrea Doria 2, 37066 Sommacampagna (VR), Italy
CodeTC-SEQ
Cost 1940 euro 
Category: 

Managing parameters on Microplan test rigs

 

TitleManaging parameters on Microplan test rigs 
AttendeesOperators of the quality assurance service, operators of the laboratory, operators of the maintenance service
ObjectivesProvide comprehensive information for a self-sufficient management and modification of the parameters of Microplan test rigs
RequirementsBasic informatics knowledge, advanced knowledge of Microplan test rigs
Program

Basic operations: 

  • Individuation of the parameters 
  • Thresholds changing
  • Inserting/modifying operators
  • Modifying operators messages
  • Modifying error messages
  • Inserting documents, pictures, movies, ecc. in the help tool
  • Modifying the electric safety test parameters

Operations with the test sequences:

  • Saving the test sequences on the hard disk
  • Matching codes/sequences
  • Duplicating sequences
  • Creating back up copies of the test sequences
Duration4 hours
LocationMicroplan, Via Andrea Doria 2, 37066 Sommacampagna (VR), Italy
CodeTC-PAR
Cost 240 euro 
Category: 

Calibration of Microplan test benches

 

TitleCalibration of Microplan test rigs 
AddresseesOperators of the quality assurance department, operators of the laboratory, operators of the maintenance service
Objectives

Provide comprehensive information for a self-sufficient execution of the correct operations for the calibration of Microplan test rigs

RequirementsBasic knowledge of Microplan test rigs, basic knowledge of the transducers
Program
  • Metrology concepts
  • Kind of transducers 
  • The process of signal acquisition
  • Reading hydraulic and pneumatic drawings
  • Which transducers need calibration 
  • Frequency of the calibration
  • Calibration of temperature transducers
  • Calibration of pressure transducers
  • Calibration of water flow transducers
  • Calibration of gas flow transducers
  • Calibration of electric power transducers
  • Using the diagnostic program
  • Using the calibration point editor
Duration8 hours
VenueMicroplan, Via Andrea Doria 2, 37066 Sommacampagna (VR), Italy
CodeTC-CAL
Cost560 euro

Ordinary maintenance of Microplan test rigs

 

TitleOrdinary maintenance of Microplan test rigs 
Attendees 

Operators of the final test, operators of the maintenance service

ObjectivesProvide comprehensive information for a self-sufficient execution of the correct operations for the ordinary maintenance of Microplan test rigs 
RequirementsBasic knowledge of Microplan test rigs, basic knowledge of transducers
Program

Periodic operations: 

  • Reading hydraulic and pneumatic drawings
  • Components identification
  • Filters cleaning
  • Water pressure regulators cleaning
  • Gas pressure regulators checking
  • Manometers checking
  • Cleaning the filters of the fans of the electric cabinet
  • Checking the correct operation of on-off pneumatic valves and proportional valves
  • Checking and replacing fuses in the electric cabinet
  • Checking the transducers correct operations 
  • Checking emergency-reset circuit
  • Checking the safety devices
  • Checking lamps and buttons
  • Reading measurements in physics values (bar, l/m, ecc.)
  • Reading measurements in electric values (mA, Volt)

Using the diagnostic program:

  • DI signals (Digital Inputs)
  • DO signals (Digital Outputs)
  • AI signals (Analog Inputs)
  • AO signals (Analog Outputs)
  • Checking the eletric safety tests unit
  • Testing the communication with the PCB
  • Testing the PWM signal
  • Operating the test rig in manual mode

Faults finding and fixing (troubleshooting):

  • Analysis and comment of troubleshooting documents
  • Using the diagnostic program as faults finding tool
Duration4 hours
VenueMicroplan, Via Andrea Doria 2, 37066 Sommacampagna (VR), Italy
CodeTC-MAN 
Cost

240 euro

Category: 
Subscribe to RSS - Courses